4544V CR32503 A1205A2731 A1205Q2591 A11205A2731 A1205U1945 For Meritor
A1205K2429
4544V
M10A11205A2731
R945010
Product Description
A1205Q2591 alternatives for
A1205K2429
4544V
M10A11205A2731
R945010
STANDARD OIL COOLER READY
MTC-4213 SERIES TRANSFER CASE | |||||||||||||||||
Item | Part Name | Qty. | Part Number | Description | |||||||||||||
1 | Lock Nut | 4 | 40-X-1233 | M45 x 1.5 thd. | |||||||||||||
2 | Washer | 4 | 1229-N-1730 | 1.79" ID x 3.00" OD x .19" wide | |||||||||||||
3 | Unitized Seal - Rear Output | 1 | R945010 | 3.25" ID x 5.51" OD x .86" long | |||||||||||||
4 | Bearing Cup | 7 | HM212011 | 4.8125" OD cup | |||||||||||||
5 | Plug (Shipping) | 3 | 1779-F-344 | ||||||||||||||
6 | Shift Cylinder | 2 | 3261-A-1067 | ||||||||||||||
7 | Bearing Cone | 7 | HM212049 | 2.625" ID cone | |||||||||||||
8 | Spacer | 1 | 2803-D-3124 | .362" Thick | |||||||||||||
9 | O-Ring | 2 | 5-X-1326 | 1.459" ID x .208" thick | |||||||||||||
10 | O-Ring | 2 | 5-X-1290 | .734" ID x .139" thick | |||||||||||||
11 | Piston (Outer) | 1 | 2230-Q-1369 | ||||||||||||||
12 | Reducer Bushing | 1 | 2206-Q-1447 | ||||||||||||||
12a | Neutral Breather | 1 | A-1199-C-1043 | ||||||||||||||
12b | Blow-by Breather | 1 | A-1199-C-1043 | Use with 3289-E-1097 cover only | |||||||||||||
13 | Cover - Transfer | 1 | 3289-K-1077 | Replaced by 3289-E-1097 | |||||||||||||
1 | 3289-E-1097 | Thicker wall | |||||||||||||||
14 | Snap Ring | 2 | 1229-A-4857 | .689" ID | |||||||||||||
15 | Capscrew (Speed Sensor Retainer) | 1 | S244-2 | ||||||||||||||
16 | O-Ring (Outer) | 1 | 5-X-1292 | 1.17" ID x .139" thick | |||||||||||||
17 | Piston (Inner) | 1 | 2230-T-1346 | ||||||||||||||
18 | O-Ring (Housing) | 2 | 5-X-1291 | .984" ID x .139" thick | |||||||||||||
19 | High Input Gear | 1 | 3892-F-5674 | ||||||||||||||
20 | Shift Shaft | 1 | 2244-T-1190 | ||||||||||||||
21 | Washer (Speed Sensor Retainer) | 1 | 1229-X-5094 | ||||||||||||||
22 | Bearing Cup | 1 | HM813810 | 5.00" OD cup | |||||||||||||
23 | Washer | 26 | 1229-E-1513 | .47" ID x .81" OD x .09" wide | |||||||||||||
24 | Capscrew | 26 | S2714A-2 | 7/16"-14 thd x 1.75" | |||||||||||||
25 | Shift Fork | 1 | 3296-Q-1317 | ||||||||||||||
26 | Bolt/Capscrew | 1 | S1712A-2 | ||||||||||||||
27 | Bolt/Capscrew | 1 | S1612A-2 | ||||||||||||||
28 | Shaft - Rear Output | 1 | 3297-V-1452 | ||||||||||||||
29 | Bearing Cup | 1 | NP682041 | Pocket bearing | |||||||||||||
30 | Bearing Cone | 1 | NP674708 | Pocket bearing | |||||||||||||
31 | Collar - Clutch | 1 | 3107-K-1181 | ||||||||||||||
32 | Gear - Input (Low) | 1 | 3892-T-5662 | ||||||||||||||
33 | Plug - Oil Restriction | 1 | 1250-M-1313 | .090" orifice | |||||||||||||
34 | Shaft - Input | 1 | 3297-T-1450 | Requires Spacer 2803-J-3312. Replaced by 3297-J-1544. |
|||||||||||||
1 | 3297-J-1544 | Replaces Input Shaft 3297-T1450 and Spacer 2803-J-3312. Service with KIT 2591 |
|||||||||||||||
34a | Spacer | 1 | 2803-J-3312 | For use with 3297-T-1450 Input Shaft only. |
|||||||||||||
35 | Snap Ring | 1 | 1229-J-4950 | Use with shafts 3297-T-1450 or 3297-T-1528 only. |
|||||||||||||
1 | 1229-P-4800 | Use with shaft 3297-J-1544 only. | |||||||||||||||
36 | Bearing Cone | 2 | HM813843 | 2.4375" ID cone | |||||||||||||
37 | Gear - Front Output | 1 | 3892-Z-5668 | ||||||||||||||
38 | Spring | 1 | 2258-U-411 | ||||||||||||||
39 | Fork-Shift | 1 | 3296-Z-1326 | Replaces A-3296-A-1093 | |||||||||||||
40 | Push Rod | 1 | 2244-S-1189 | ||||||||||||||
41 | Gear - Transfer | 1 | 3297-N-1444 | ||||||||||||||
42 | Shaft - Front Output | 1 | 3892-H-5672 | ||||||||||||||
43 | Collar - Clutch | 1 | 3107-J-1284 | Replaces 3107-M-1183 | |||||||||||||
MTC-4213 SERIES TRANSFER CASE | |||||||||||||||||
Item | Part Name | Qty. | Part Number | Description | |||||||||||||
44 | Dowel | 2 | 1246-T-1190 | .375" dia x 1.00" long | |||||||||||||
45 | Magnet | 3 | 2297-K-6771 | ||||||||||||||
46 | Plug | 4 | P-26 | 3/8"-18 NPT | |||||||||||||
47 | Piston | 1 | 2230-T-1190 | ||||||||||||||
48 | Drain Plug - Magnetic | 1 | 1250-E-473 | 3/4"-14 NPT square socket | |||||||||||||
49 | Fitting Assy (Screen / Elbow) | 1 | A-2206-U-1347 | 3/4"-14 NPT | |||||||||||||
50 | Pump Assy. | 1 | A-3303-G-1047 | Replaces A-3303-P-1030. Must use A-3226-Z-1482 Input Cage. |
|||||||||||||
51 | Valve - Pressure Relief | 1 | 2297-U-5273 | ||||||||||||||
52 | Spring - Relief Valve | 1 | 2258-Z-1118 | ||||||||||||||
53 | Capscrew | 7 | S2814A-2 | 1/2"-13 thd x 1.75" | |||||||||||||
54 | Washer | 7 | 1229-C-1511 | .53" ID x .88" OD x .09" wide | |||||||||||||
55 | Cage - Input Bearing | 1 | A-3226-Z-1482 | Non-Oil Cooler version | |||||||||||||
1 | A-3226-W-1479 | Oil Cooler ready | |||||||||||||||
56 | O-Ring | 1 | 5-X-1327 | 7.483" x .139" thick | |||||||||||||
57 | Male Connector | 1 | 2206-V-1348 | Non-Oil Cooler version | |||||||||||||
1 | 2206-C-1485 | Oil Cooler ready | |||||||||||||||
58 | Capscrew | 6 | MS208045-1 | M8 x 1.25 | |||||||||||||
59 | Washer | 6 | 1229-E-1669 | .34" ID x .62" OD x .06" wide | |||||||||||||
60 | Fill Plug | 1 | P-212 | 3/4"-14 NPT | |||||||||||||
61 | Breather Assy. | 1 | A-1199-P-1394 | 3/8"-18 NPT | |||||||||||||
62 | Elbow | 1 | 2206-F-1254 | 3/8"-18 NPT / 3/8"-18 NPT | |||||||||||||
63 | Tube Assy. | 1 | A-2206-R-1344 | Non-Oil Cooler version | |||||||||||||
1 | A-2206-A-1483 | Oil Cooler ready | |||||||||||||||
64 | Case - Transfer | 1 | 3290-X-1142 | Non-Oil Cooler version | |||||||||||||
1 | 3290-D-1200 | Oil Cooler ready | |||||||||||||||
65 | Gear - Idler | 1 | 3892-V-5664 | ||||||||||||||
66 | Unitized Seal - Forward Output | 1 | R945007 | 3.25" ID x 4.25" OD x .86" long | |||||||||||||
66a | Multiple-Lip Seal - Input Shaft | 1 | A1-1205-X-2728 | ||||||||||||||
67 | Speed Sensor | 1 | A-3280-U-9849 | Optional | |||||||||||||
68 | Engagement Sensor | 2 | 3237-W-1167 | Optional. Do not use with Special Screw (41-X-1022) and Washer (1229-U-1503) |
|||||||||||||
68a | Screw - Special (Sensor Plug) | 2 | 41-X-1022 | Optional M16 x 1-6g. Special Screw and Washer used in vehicles not equipped with Engagement Sensor (3237-W-1167) |
|||||||||||||
68b | Washer | 2 | 1229-U-1503 | ||||||||||||||
69 | Yoke - Input | 1 | RAP or RCE spline code *** |
2-3/8"-46T spline (No Slinger) | |||||||||||||
70 | Yoke - Front Output | 1 | 2-3/8"-46T spline (Slinger opt.) | ||||||||||||||
71 | Yoke - Rear Output | 1 | 2-3/8"-46T spline (Slinger opt.) | ||||||||||||||
72 | Shim - .003" | Use As Reqd. |
2203-K-9241 | Input bearing cage | |||||||||||||
Shim - .005" | 2203-L-9242 | ||||||||||||||||
Shim - .010" | 2203-M-9243 | ||||||||||||||||
73 | Shim - .010" | Use As Reqd. |
2803-P-3110 | Housing bearing cups | |||||||||||||
Shim - .005" | 2803-Q-3111 | ||||||||||||||||
Shim - .003" | 2803-R-3112 | ||||||||||||||||
74 | Male Connector | 2 | 2206-E-1513 | 1/2" NPT x 9/16" 37° Flare Oil Cooler ready |
|||||||||||||
75 | Loop Tube | 1 | A-2296-Q-1161 | Oil Cooler ready - for use when cooler not connected |
|||||||||||||
76 | Plug | 1 | P-28 | ||||||||||||||
MTC-4213 SERIES TRANSFER CASE | |||||||||||||||||
Item | Part Name | Qty. | Part Number | Description | |||||||||||||
Not Shown |
Spacer - .003" | Use As Reqd. |
2803-E-3125 | 2TS Rear cover bearing spacer Located next to spacer (Item 8) |
|||||||||||||
Spacer - .009" | 2803-F-3126 | ||||||||||||||||
Spacer - .015" | 2803-G-3127 | ||||||||||||||||
Spacer - .021" | 2803-H-3128 | ||||||||||||||||
MTC-4213 SERVICE KITS | |||||||||||||||||
Part Name | Part Number | Quantity | Description | ||||||||||||||
KIT 2564 | Fastener Kit | ||||||||||||||||
Lock Nut | 40-X-1233 | 4 | M45 x 1.5 thd. | ||||||||||||||
Washer | 1229-N-1730 | 4 | 1.79" ID x 3.00" OD x .19" wide | ||||||||||||||
Lock Nut | 40-X-1341 | 1 | 2.25"-12 thd. | ||||||||||||||
Washer | 1229-E-4113 | 1 | 2.28" ID x 3.25" OD x .32" wide | ||||||||||||||
Capscrew (Speed Sensor Retainer) | S244-2 | 1 | |||||||||||||||
Washer (Speed Sensor Retainer) | 1229-X-5094 | 1 | |||||||||||||||
Capscrew | S2714A-2 | 34 | 7/16"-14 thd x 1.75" | ||||||||||||||
Washer - Hardened | 1229-E-1513 | 34 | |||||||||||||||
Bolt/Capscrew | S1712A-2 | 1 | |||||||||||||||
Bolt/Capscrew | S1612A-2 | 1 | |||||||||||||||
Plug - Oil Restriction | 1250-M-1313 | 1 | .090" orifice | ||||||||||||||
Dowel | 1246-T-1190 | 2 | .375" dia x 1.00" long | ||||||||||||||
Drain Plug - Magnetic | 1250-E-473 | 1 | 3/4"-14 NPT square socket | ||||||||||||||
Plug | P-26 | 4 | 3/8"-18 NPT | ||||||||||||||
Fill Plug | P-212 | 1 | 3/4"-14 NPT | ||||||||||||||
Capscrew | MS208045-1 | 6 | M8 x 1.25 | ||||||||||||||
Washer - Flat | 1229-E-1669 | 6 | .34" ID x .62" OD x .06" wide | ||||||||||||||
Capscrew | S-2814A-2 | 7 | 1/2"-13 thd x 1.75" | ||||||||||||||
Washer - Hardened | 1229-C-1511 | 7 | .53" ID x .88" OD x .09" wide | ||||||||||||||
Male Connector | 2206-C-1485 | 1 | 3/4"-14 NPT / 1 1/16"-12 Flare | ||||||||||||||
Screw - Special (Sensor Plug) | 41-X-1022 | 2 | Optional M16 x 1-6g | ||||||||||||||
Washer | 1229-U-1503 | 2 | |||||||||||||||
KIT 2566 Shim Kit | |||||||||||||||||
Shim - .003" | 2203-K-9241 | 5 | Input bearing cage | ||||||||||||||
Shim - .005" | 2203-L-9242 | 5 | |||||||||||||||
Shim - .010" | 2203-M-9243 | 5 | |||||||||||||||
Shim - .010" | 2803-P-3110 | 5 | Housing bearing cups | ||||||||||||||
Shim - .005" | 2803-Q-3111 | 5 | |||||||||||||||
Shim - .003" | 2803-R-3112 | 5 | |||||||||||||||
Spacer - .003" | 2803-E-3125 | 5 | 2TS Rear cover bearing spacer | ||||||||||||||
Spacer - .009" | 2803-F-3126 | 5 | |||||||||||||||
Spacer - .015" | 2803-G-3127 | 5 | |||||||||||||||
Spacer - .021" | 2803-H-3128 | 5 | |||||||||||||||
KIT 2591 | Input Shaft Kit | ||||||||||||||||
Shaft - Input | 3297-J-1544 | 1 | |||||||||||||||
Snap Ring | 1229-P-4800 | 1 | |||||||||||||||
Plug - Oil Restriction | 1250-M-1313 | 1 | |||||||||||||||
MTC-4213 SERVICE KITS (cont) | |||||||||||||||||
Part Name | Part Number | Quantity | Description | ||||||||||||||
KIT 2596 | Shift Fork/Collar Kit | ||||||||||||||||
Collar - Clutch | 3107-J-1284 | 1 | |||||||||||||||
Shift Fork | 3296-Z-1326 | 1 | |||||||||||||||
KIT 2597 | Seal/Snap Ring Kit | ||||||||||||||||
Unitized Seal - Forward Output | R945007 | 1 | 3.25" ID x 4.25" OD x .86" long | ||||||||||||||
Unitized Seal - Rear Output | R945010 | 1 | 3.25" ID x 5.51" OD x .86" long | ||||||||||||||
Multiple-Lip Seal - Input Shaft | A1-1205-X-2728 | 1 | 3.25" ID x 4.25" OD x .58" long | ||||||||||||||
O-Ring | 5-X-1326 | 2 | 1.459" ID x .208" thick | ||||||||||||||
O-Ring (Inner) | 5-X-1290 | 2 | .734" ID x .139" thick | ||||||||||||||
Snap Ring | 1229-U-4857 | 2 | .689" ID | ||||||||||||||
O-Ring | 5-X-1292 | 1 | 1.71" ID x .139" thick | ||||||||||||||
O-Ring (Housing) | 5-X-1291 | 2 | .984" ID x .139 thick | ||||||||||||||
O-Ring | 5-X-1327 | 1 | 7.483" x .139" thick | ||||||||||||||
KIT 2598 | Shift Cylinder Kit | ||||||||||||||||
Shift Cylinder | 3261-A-1067 | 1 | |||||||||||||||
O-Ring | 5-X-1326 | 1 | |||||||||||||||
O-Ring (Inner) | 5-X-1290 | 1 | |||||||||||||||
Piston (Outer) | 2230-Q-1369 | 1 | |||||||||||||||
KIT 2599 | Oil-Cooler Retrofit Kit | ||||||||||||||||
Case - Fin. | 3290-D-1200 | 1 | |||||||||||||||
Input Bearing Cage Assy. | A-3226-W-1479 | 1 | |||||||||||||||
Tube Assy. | A-2296-Q-1161 | 1 | |||||||||||||||
Tube Assy. | A-2206-A-1483 | 1 | |||||||||||||||
Male Connector | 2206-C-1485 | 1 | 3/4"-14 NPT / 1 1/16"-12 Flare | ||||||||||||||
Fitting | 2206-E-1513 | 2 | 1/2" NPT x 9/16" 37° Flare | ||||||||||||||
Unitized Seal - Forward Output | R945007 | 1 | 3.25" ID x 4.25" OD x .86" long | ||||||||||||||
Unitized Seal - Rear Output | R945010 | 1 | 3.25" ID x 5.51" OD x .86" long | ||||||||||||||
Multiple-Lip Seal - Input Shaft | A1-1205-X-2728 | 1 | 3.25" ID x 4.25" OD x .58" long | ||||||||||||||
O-Ring | 5-X-1326 | 1 | 1.459" ID x .208" thick | ||||||||||||||
O-Ring | 5-X-1327 | 2 | 7.483" x .139" thick | ||||||||||||||
O-Ring (Inner) | 5-X-1290 | 1 | .734" ID x .139" thick | ||||||||||||||
O-Ring (Housing) | 5-X-1291 | 2 | .984" ID x .139 thick | ||||||||||||||
O-Ring | 5-X-1292 | 1 | 1.71" ID x .139" thick | ||||||||||||||
Plug | P-28 | 1 | |||||||||||||||
SEAL REPLACEMENT | |||||||||||||||||
Meritor has released the Multiple-Lip Seal (MLS) for use in the INPUT POSITION ONLY on the MTC-4208, -4210 and -4213 transfer cases. The multiple-lip seal is compatible with the current input shaft sealand can be used in service. |
|||||||||||||||||
Transfer Case Model | Seal Position | Seal Service Part Number |
Previous Seal Part Number |
Seal Driver | Sleeve Driver | ||||||||||||
MTC-4208, -4210 and -4213 | Input Shaft | A1-1205X2728 | R945007 | 2728T1 | 2728T2 | ||||||||||||
MTC-4208 and -4210 | Forward and Rear Output | R945007 | A-1205R2592 | KIT 4454 | NA | ||||||||||||
MTC-4213 | Forward Output | R945007 | A-1205R2592 | KIT 4454 | NA | ||||||||||||
MTC-4213 | Rear Output | R945010 | A-1205Q2591 | KIT 4454 | NA | ||||||||||||
MTC-4208 and -4210 | PTO Seal | R945008 | A-1205P2590 | KIT 4454 | NA | ||||||||||||
MTC-4213 YOKES | |||||||||||||||||
Yoke Location | ArvinMeritor Part Number |
Yoke Description |
Spline Size | ||||||||||||||
Front Input | 3260-S-1813 | Easy Service | 2-3/8"-46T | ||||||||||||||
see note (1) | Other styles | 2-3/8"-46T | |||||||||||||||
Front Output | 140TYS38A | SPL140 | 2-3/8"-46T | ||||||||||||||
see note (1) | Other styles | 2-3/8"-46T | |||||||||||||||
Rear Output | 140TYS38A | SPL140 | 2-3/8"-46T | ||||||||||||||
170TYS38-4A | SPL170 | 2-3/8"-46T | |||||||||||||||
see note (1) | Other styles | 2-3/8"-46T |
FAQ
Q1. What is the payment term?
A: We accept a T/T 30% deposit and a 70% balance of a current bill of lading or a letter of credit.
Q2. What is the normal delivery time for product orders?
A: The average delivery time of the sample is 1-2 weeks. If the mold production is involved, the delivery cycle of the production mold is 10 days, and the average production time after the sample is approved is 1-2 weeks.
Q3. What is your standard packaging?
A: All goods will be packed in PE bags and then packed in cartons and filled with trays. Special packaging methods are accepted when needed, but charges may apply.
Q4. Which certificate do you have?
A1: we have passed ISO, IATF still applying for more patents.
Q5: How to check the quality of bulk orders?
A1: Our inspection procedures include, first inspection/patrol inspection/initial inspection/full inspection/shipment inspection.
A2: We provide quality certification to all customers before delivery, such as measurement reports, material data sheets, etc. A3: We accept third party inspections such as SGS, TUV, INTERTEK, BV, etc.
Q6: How do I choose a raw compound for my application?
A: With years of experience in using a variety of materials, we can help you choose the material that best suits your needs, keeping in mind the cost of materials.
Q7: Can you provide materials of different colors?
A: Yes, we can produce custom molded rubber and silicone rubber products in different colors. Color codes are required when ordering.
Q8: From which side can you produce which materials?
A: NBR, EPDM, silicone, FKM, NEOPRENE (CR), NR, IIR, SBR, ACM, AEM, fluorosilicon (FVMQ), FFKM, liquid silica gel, and the like.